Inquiry

eye bolt angle chart

TECHNICAL COLLARED EYEBOLT WORKING LOAD CHART

collared eyebolt working load chart collared eyebolt working load chart tel. +44 (0)1384 563356 | fax. +44 (0)1384 563357 www.brooksforgings.co.uk note: this method is correct for collared eyebolts as illustrated and pair of eyebolts when the angle between sling legs is:

Learn More

Range from 100kg to 30,000kg - LiftingSafety

Material: As specified by BS 4278 Hardened and Tempered S.W.L. Shown at 0° (vertical) angle of lift. Safety Note: Eyebolts under M12 are not recommended for lifting. Non-standard thread pitches available upon request. Various sizes from M6 to M80. Capacities (SWL - Safe working Load) from 100kg up to 30t. Self-coloured finish as standard.

Learn More

Shoulder Eye Bolts and Swivel Hoist Rings Load Limits - Certified Slings

Always apply load to eye bolt in the plane of the eye. Quenched & Tempered • Design Factor 5/1 Swivel Hoist Rings When using lifting slings of two or more legs make sure the forces in the leg are calculated. Select the proper size swivel hoist ring to allow for load in sling leg. Always insure hoist ring is free to align itself with sling.

Learn More

Eye Bolts 101: How to Safely Select and Use the Right Eye Bolt For You

As soon as a lift begins to occur at any other angle, referred to as angular lift, the rated capacity of the eye bolt begins to diminish. The greater the angle the more drastically the rated capacity is reduced. The chart below shows the impact the direction of pull has on rated capacity: Direction of Pull Rated Capacity

Learn More

A Guide for Eye Bolts and Lifting Points - Types and Safe Use

Dynamo Eyebolts - For Axial loads only (NOT TO BE USED FOR ANGLED LIFTS) vertical (axial lift ) will reduce the rating capacity refer to load charts.

Learn More

Materials Handling - Lifting With Eye Bolts : OSH Answers

Use a spreader bar with regular (non-shoulder) eye bolts to keep the lift angle at 90° to the horizontal. Use eye bolts at a horizontal angle greater than 45°. Sling strength at 45° is 71% of vertical sling capacity. Eye bolt strength at 45° horizontal angle drops down to 30% of vertical lifting capacity. Use a swivel hoist ring for angled

Learn More

Eye Bolts - Shouldered & Non-Shouldered Eye Bolts & Machinery Eye Bolt

Eye Bolts are load rated and made from forged steel that has been quenched and tempered. Bishop Lifting offers Regular Eyebolts along with Shoulder Eye Bolts, and Shoulder Type Machinery Eye Bolts. All of our eye bolts meet or exceed the requirements of ASME B30.26 including identification, ductility, design factor, proof load, and temperature

Learn More

Forged Machinery Eye Bolts - The Crosby Group

All bolts threaded UNC. • Forged Steel - Quenched & Tempered. • Working Load Limits shown are for in-line pull. For angle loading, see page 196. • Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these bolts meet other critical

Learn More

forged eye bolt warnings and application instructions

Load may slip or fall if proper eye bolt assembly diagrams and charts below before using eye bolt assemblies. angle of loading on the eye bolt.

Learn More

Guys and Anchors - Jea

downguys at bolt hole 73) - See plate GY7SPL. Provisions for downguys are also provided on the steel crossarm and the 3-phase cutout and arrester bracket if required. E. GUY ANCHORS Two basic types of anchoring systems are used for downguys -- one is the screw type and the other is the "Manta-Ray" type.

Learn More

A Guide for Eye Bolts and Lifting Points - Types and Safe Use. - DLH Online

A tolerance of ±5º is acceptable but it is a matter of luck whether this will be achieved when first screwed in because the eyebolt manufacturer has no control over the start point of the threaded hole. Therefore it is permissible to shim up to half the screw pitch to achieve the correct orientation.

Learn More

What Are The Different Types of Eye Bolts Used for Overhead Lifts

These eye bolts are designed with a shoulder at the point where the eye and the shank come together. This shoulder design reduces bending stresses on the shank and allows the eye bolt to be used for angular lifting if the shoulder is properly seated in the load.

Learn More

Forged Eye Bolt Capacity and Strength - Amesweb

Forged Eye Bolt Capacity and Strength Chart to show rated load capacities, must always be applied to eye bolts in the plane of the eye, not at an angle.

Learn More

eyebolts - rigging

THE CROSBY GROUP. REGULAR NUT EYE BOLTS. G-291. Recommended for straight line pull. All Bolts Hot Dip galvanized after threading (UNC). Furnished with standard Hot Dip galvanized hex nuts. Forged Steel — Quenched and Tempered. Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles. Shank.

Learn More

PDF FORGED EYE BOLT WARNINGS AND APPLICATION INSTRUCTIONS WARNING Shoulder ...PDF

and charts below before using eye bolt assemblies. Table 2 (in-Line) Metric Size Working Load Limit - kg m6 200 m8 400 m10 640 m12 1000 m16 1800 m20 2500 † Always apply load to eye bolt in the plane of the eye - not at an angle. † Never exceed the capacity of the eye bolt-see Table I & 2. † When using lifting slings of two or more

Learn More

LIFTING EYES - Green Pin

Van Beest offers a wide range of other lifting eye bolts, eye nuts and OL and EL eyebolts/nuts are valid for in-line lifting only up to an angle of 30°.

Learn More